{"id":19195,"date":"2026-10-17T10:48:34","date_gmt":"2026-10-17T02:48:34","guid":{"rendered":"https:\/\/www.wehopower.com\/news\/tx4-s-injection-molding-barrel-heating-zones\/"},"modified":"2026-10-19T12:07:53","modified_gmt":"2026-10-19T04:07:53","slug":"tx4-s-injection-molding-barrel-heating-zones","status":"publish","type":"news","link":"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/","title":{"rendered":"TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor"},"content":{"rendered":"<article>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_86 counter-hierarchy ez-toc-counter ez-toc-grey ez-toc-container-direction\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\" style=\"cursor:inherit\">\u03a0\u03af\u03bd\u03b1\u03ba\u03b1\u03c2 \u03c0\u03b5\u03c1\u03b9\u03b5\u03c7\u03bf\u03bc\u03ad\u03bd\u03c9\u03bd<\/p>\n<span class=\"ez-toc-title-toggle\"><a href=\"#\" class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" aria-label=\"Toggle Table of Content\"><span class=\"ez-toc-js-icon-con\"><span class=\"\"><span class=\"eztoc-hide\" style=\"display:none;\">\u039c\u03c0\u03b1\u03c1\u03ad\u03c4\u03b1<\/span><span class=\"ez-toc-icon-toggle-span\"><svg style=\"fill: #999;color:#999\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" class=\"list-377408\" width=\"20px\" height=\"20px\" viewbox=\"0 0 24 24\" fill=\"none\"><path d=\"M6 6H4v2h2V6zm14 0H8v2h12V6zM4 11h2v2H4v-2zm16 0H8v2h12v-2zM4 16h2v2H4v-2zm16 0H8v2h12v-2z\" fill=\"currentColor\"><\/path><\/svg><svg style=\"fill: #999;color:#999\" class=\"arrow-unsorted-368013\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"10px\" height=\"10px\" viewbox=\"0 0 24 24\" version=\"1.2\" baseprofile=\"tiny\"><path d=\"M18.2 9.3l-6.2-6.3-6.2 6.3c-.2.2-.3.4-.3.7s.1.5.3.7c.2.2.4.3.7.3h11c.3 0 .5-.1.7-.3.2-.2.3-.5.3-.7s-.1-.5-.3-.7zM5.8 14.7l6.2 6.3 6.2-6.3c.2-.2.3-.5.3-.7s-.1-.5-.3-.7c-.2-.2-.4-.3-.7-.3h-11c-.3 0-.5.1-.7.3-.2.2-.3.5-.3.7s.1.5.3.7z\"\/><\/svg><\/span><\/span><\/span><\/a><\/span><\/div>\n<nav><ul class='ez-toc-list ez-toc-list-level-1' ><li class='ez-toc-page-1 ez-toc-heading-level-1'><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#TX4-S_for_Injection_Molding_Barrels_Define_Each_Heating_Zone_and_Its_Sensor\" >TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor<\/a><ul class='ez-toc-list-level-2' ><li class='ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Map_the_feedback_loop_before_ordering_controllers\" >Map the feedback loop before ordering controllers<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Keep_the_measured_point_tied_to_the_correct_zone\" >Keep the measured point tied to the correct zone<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Specify_the_switching_branch_separately_from_the_controller\" >Specify the switching branch separately from the controller<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Put_the_operator_interface_in_a_suitable_panel\" >Put the operator interface in a suitable panel<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Commission_the_zones_as_identifiable_loops\" >Commission the zones as identifiable loops<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#What_to_include_in_a_molding-temperature_inquiry\" >What to include in a molding-temperature inquiry<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Frequently_asked_questions\" >Frequently asked questions<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Can_one_TX4-S_independently_control_three_barrel_zones\" >Can one TX4-S independently control three barrel zones?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Does_the_same_PV_in_two_zones_mean_the_material_temperature_is_identical\" >Does the same PV in two zones mean the material temperature is identical?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/www.wehopower.com\/el\/news\/tx4-s-injection-molding-barrel-heating-zones\/#Can_the_PID_settings_from_one_zone_be_copied_to_the_others\" >Can the PID settings from one zone be copied to the others?<\/a><\/li><\/ul><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h1><span class=\"ez-toc-section\" id=\"TX4-S_for_Injection_Molding_Barrels_Define_Each_Heating_Zone_and_Its_Sensor\"><\/span>TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor<span class=\"ez-toc-section-end\"><\/span><\/h1>\n<figure data-image-role=\"application_a\"><img fetchpriority=\"high\" decoding=\"async\" src=\"https:\/\/i1.wp.com\/www.wehopower.com\/wp-content\/uploads\/2026\/10\/01-application-a-77.png?quality=85&#038;strip=all\" alt=\"TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor  title=\" width=\"1536\" height=\"1024\" tx4-s for injection molding barrels: define each heating zone and its sensor title=\"\"><figcaption>Conceptual single-zone arrangement. The illustrated PV 198 and SV 200 are explanatory numbers, not measured process data or a recommended molding recipe.<\/figcaption><\/figure>\n<p>For an injection-molding barrel, select a PID temperature controller by the heating zone it will control, not simply by the number of heater bands on the machine. The TX4-S W1T\/R-2 has one sensor-input channel for its feedback loop. Each zone that needs an independently controlled temperature must have an appropriately assigned sensor, control channel and heater-switching branch.<\/p>\n<p>A useful purchase specification therefore begins with a zone map: which part of the barrel is being measured, which heaters respond to that reading, and what the process expects from that zone. A controller model alone does not define the complete molding-temperature system.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Map_the_feedback_loop_before_ordering_controllers\"><\/span>Map the feedback loop before ordering controllers<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>A physical heater band and a controlled zone are not necessarily the same thing. Several bands may form one engineered heating branch, while a nozzle may need a separate temperature target. Let the machine&#8217;s thermal and electrical design establish the grouping. Do not join independently required zones merely to reduce the controller count.<\/p>\n<p>For a TX4-based arrangement, give each independently controlled loop its own controller assignment. The following is an identification example, not a recommended temperature profile or a wiring diagram.<\/p>\n<table>\n<thead>\n<tr>\n<th>Zone record<\/th>\n<th>What must be identified<\/th>\n<th>Why it matters<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Barrel zone A<\/td>\n<td>Its sensor location, controller tag and assigned heater branch.<\/td>\n<td>The reading and the output must belong to the same intended thermal region.<\/td>\n<\/tr>\n<tr>\n<td>Barrel zone B<\/td>\n<td>Its own input, switching branch and permitted operating range.<\/td>\n<td>A neighboring display must not be mistaken for this zone&#8217;s feedback.<\/td>\n<\/tr>\n<tr>\n<td>Nozzle zone<\/td>\n<td>The nozzle sensor and heater arrangement defined by the machine builder.<\/td>\n<td>A barrel reading does not automatically represent the nozzle.<\/td>\n<\/tr>\n<tr>\n<td>Whole machine<\/td>\n<td>Heat-enable conditions, alarm response and independent protective functions.<\/td>\n<td>Individual PID loops do not by themselves define machine safety.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2><span class=\"ez-toc-section\" id=\"Keep_the_measured_point_tied_to_the_correct_zone\"><\/span>Keep the measured point tied to the correct zone<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The TX4 input must match the installed sensor type. The matched manual lists thermocouple inputs K, E, J, N, T, S, R and B, plus Pt100 and Cu50 RTD inputs, with different usable ranges. This is a choice of input configuration, not permission to substitute sensors without checking the application and wiring.<\/p>\n<p>Record the probe type, physical position, contact arrangement and cable identification for each zone. After heater or sensor maintenance, verify that the sensor has returned to its specified position and that its cable still reaches the intended input. A plausible temperature value is not proof that the correct zone is being measured.<\/p>\n<p>As a general thermal-control principle, the controller adjusts heat in response to a sensor measurement of the heated object. The <a href=\"https:\/\/www.omron.com\/global\/en\/technology\/omrontechnics\/vol51\/020.html\" target=\"_blank\" rel=\"noopener\">referenced discussion of temperature-control conditions<\/a> includes molding cylinders and explains how sensor relocation can change the thermal response even when the controller indication appears normal. This supports checking the physical measurement location; it does not establish any additional TX4 functions.<\/p>\n<p>A barrel-mounted sensor reports temperature at that measurement point. Do not describe its PV as a direct measurement of all the molten material inside the barrel or as a guarantee of molded-part quality. Those requirements need the machine&#8217;s own process measurements and acceptance criteria.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Specify_the_switching_branch_separately_from_the_controller\"><\/span>Specify the switching branch separately from the controller<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The controller&#8217;s output interface and the heater&#8217;s power circuit are different purchasing items. For the matched TX4 manual, the SSR drive is 12 VDC \u00b12 V at no more than 20 mA. It is a signal for a suitable external switching device, not a supply that can power a barrel heater.<\/p>\n<p>Give the panel builder each zone&#8217;s heater voltage and load, the required switching interface and the protective arrangement. The switching device, its heat management and the branch protection must be selected for that circuit. Do not select heater power from the front-panel OUT indication or from the controller&#8217;s own supply rating.<\/p>\n<p>The photographed W1 version identifies Alarm 1. AL1 and AL2 on common front-panel artwork are alarm legends, not two extra temperature-control channels. Confirm the full delivered order code when specifying spare units.<\/p>\n<figure data-image-role=\"product_detail\"><img decoding=\"async\" src=\"https:\/\/i1.wp.com\/www.wehopower.com\/wp-content\/uploads\/2026\/10\/03-product-detail-73.png?quality=85&#038;strip=all\" alt=\"TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor  title=\" width=\"1536\" height=\"1024\" tx4-s for injection molding barrels: define each heating zone and its sensor title=\"\"><figcaption>Original model photographs support the controller identity. Input channels, output interface and installation follow the matched TX4 manual.<\/figcaption><\/figure>\n<h2><span class=\"ez-toc-section\" id=\"Put_the_operator_interface_in_a_suitable_panel\"><\/span>Put the operator interface in a suitable panel<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The TX4-S is inserted through a panel and secured by its rear retaining bracket. Its long housing belongs behind the panel, leaving the front interface accessible to the operator. It is not a DIN-rail module and should not be placed directly against the heated barrel.<\/p>\n<p>The matched manual specifies an operating ambient of \u221210 to 50\u00b0C and warns against unsuitable heat, vibration and other installation conditions. Check the air around the installed controller inside the actual panel, not just the workshop temperature. Arrange the enclosure and cable routes so hot-machine surfaces do not become the controller&#8217;s mounting environment.<\/p>\n<figure data-image-role=\"application_b\"><img decoding=\"async\" src=\"https:\/\/i1.wp.com\/www.wehopower.com\/wp-content\/uploads\/2026\/10\/02-application-b-74.png?quality=85&#038;strip=all\" alt=\"TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor  title=\" width=\"1536\" height=\"1024\" tx4-s for injection molding barrels: define each heating zone and its sensor title=\"\"><figcaption>A separate nozzle-zone interface illustrates why the panel tag, sensor and heater branch need a consistent identity. The original face is shown unlit; the scene does not validate a temperature profile.<\/figcaption><\/figure>\n<h2><span class=\"ez-toc-section\" id=\"Commission_the_zones_as_identifiable_loops\"><\/span>Commission the zones as identifiable loops<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Before tuning, qualified personnel should confirm the sensor-to-zone and output-to-heater assignments under the machine&#8217;s approved commissioning procedure. Marking the panel, cable and drawing with the same zone tag helps prevent an otherwise convincing but incorrect connection from surviving maintenance.<\/p>\n<p>Next, establish the intended sensor configuration, operating unit, setpoint limits and output interface for that loop. Assess the response under the relevant machine conditions, including how the other zones are being operated. A set of PID values from one position is not automatically appropriate for every barrel section or nozzle.<\/p>\n<p>TX4 auto-tuning can determine control parameters for the connected loop; it does not identify which physical heater or sensor the installer meant to connect. Treat any tuning outcome as part of commissioning that particular assembly. Keep the process temperature profile and startup sequence under the machine builder&#8217;s approved instructions rather than borrowing the illustrative readout in an article image.<\/p>\n<p>Finally, define what happens when a sensor, controller or switching device fails. The TX4 manual calls for fail-safe measures where a failure could create a hazardous condition. A normal control alarm must not silently replace an independently required overtemperature protective function.<\/p>\n<figure data-image-role=\"engineering_context\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/i1.wp.com\/www.wehopower.com\/wp-content\/uploads\/2026\/10\/04-engineering-context-77.png?quality=85&#038;strip=all\" alt=\"TX4-S for Injection Molding Barrels: Define Each Heating Zone and Its Sensor  title=\" width=\"1536\" height=\"1024\" tx4-s for injection molding barrels: define each heating zone and its sensor title=\"\"><figcaption>A zone map should identify the whole feedback loop, not only a controller or heater-band quantity.<\/figcaption><\/figure>\n<h2><span class=\"ez-toc-section\" id=\"What_to_include_in_a_molding-temperature_inquiry\"><\/span>What to include in a molding-temperature inquiry<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Send the number of independently controlled zones, their location names, sensor types and ranges, heater electrical data, chosen switching interface, controller supply and panel conditions. Include a zone map and the required abnormal-condition response. This is more useful for model confirmation than a request for a controller that is simply \u201csuitable for injection molding.\u201d<\/p>\n<p>Use the <a href=\"https:\/\/www.wehopower.com\/el\/product\/tx4-series-tx4-s-economic-dual-display-pid-temperature-controller\/\">TX4 product information<\/a> as a starting point, then <a href=\"https:\/\/www.wehopower.com\/el\/contact\/\">send WEHO the full zone and interface requirements<\/a>. Confirm configuration and installation against the instructions supplied with the delivered model.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Frequently_asked_questions\"><\/span>Frequently asked questions<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3><span class=\"ez-toc-section\" id=\"Can_one_TX4-S_independently_control_three_barrel_zones\"><\/span>Can one TX4-S independently control three barrel zones?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Not as three independent feedback loops. The matched TX4-S has one sensor-input channel. Independent zones require appropriate separate control channels and their own assigned feedback and switching branches.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Does_the_same_PV_in_two_zones_mean_the_material_temperature_is_identical\"><\/span>Does the same PV in two zones mean the material temperature is identical?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. Each PV belongs to its configured sensor and measurement location. The material condition and temperature distribution require process-specific evaluation.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Can_the_PID_settings_from_one_zone_be_copied_to_the_others\"><\/span>Can the PID settings from one zone be copied to the others?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>They should not be accepted without checking each installed loop. Heater arrangement, sensor placement and operating conditions can differ, so commission the actual assembly rather than assuming the same response.<\/p>\n<\/article>","protected":false},"excerpt":{"rendered":"<p>Map each molding heating zone to its sensor, controller and switching branch before selecting or tuning the control loop.<\/p>","protected":false},"author":2,"featured_media":19191,"parent":0,"menu_order":49,"comment_status":"closed","ping_status":"","template":"","format":"standard","meta":{"_acf_changed":false,"_joinchat":[],"footnotes":""},"news_category":[149,284],"class_list":["post-19195","news","type-news","status-publish","format-standard","has-post-thumbnail","hentry","news_category-blog","news_category-product-articles","entry"],"acf":[],"post_mailing_queue_ids":[],"_links":{"self":[{"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/news\/19195","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/news"}],"about":[{"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/types\/news"}],"author":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/comments?post=19195"}],"version-history":[{"count":1,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/news\/19195\/revisions"}],"predecessor-version":[{"id":19623,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/news\/19195\/revisions\/19623"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/media\/19191"}],"wp:attachment":[{"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/media?parent=19195"}],"wp:term":[{"taxonomy":"news_category","embeddable":true,"href":"https:\/\/www.wehopower.com\/el\/wp-json\/wp\/v2\/news_category?post=19195"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}