{"id":21796,"date":"2026-11-12T16:06:11","date_gmt":"2026-11-12T08:06:11","guid":{"rendered":"https:\/\/www.wehopower.com\/news\/spd-lead-length-power-supply-terminals\/"},"modified":"2026-11-12T16:06:11","modified_gmt":"2026-11-12T08:06:11","slug":"spd-lead-length-power-supply-terminals","status":"publish","type":"news","link":"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/","title":{"rendered":"SPD Lead Length: Check Protection at the Power Supply Terminals"},"content":{"rendered":"<div class=\"weho-blog\">\n<div class=\"takeaways\">\n<p>Key Engineering Takeaways<\/p>\n<ul>\n<li>SPD connection leads add transient voltage to the device\u2019s own protection level.<\/li>\n<li>Count the complete relevant connection path, including any external SPD disconnector.<\/li>\n<li>Short leads and separated incoming\/outgoing routes address different installation problems.<\/li>\n<li>Accept the installed arrangement against the power supply\u2019s documented surge requirements.<\/li>\n<\/ul>\n<\/div>\n<figure class=\"article-figure hero\" data-asset=\"hero\"><a class=\"product-image-link\" href=\"https:\/\/www.wehopower.com\/th\/product\/ndr-dinrail-120w-ac-to-dc-single-output-switching-power-supply\/\" aria-label=\"NDR-120-24 details\"><img fetchpriority=\"high\" src=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/ndr-120-24-application-v2.webp\" alt=\"SPD Lead Length: Check Protection at the Power Supply Terminals  title=\" width=\"1200\" height=\"675\" loading=\"eager\" decoding=\"async\" spd lead length: check protection at the power supply terminals title =\"\"><\/a><figcaption>AI-assisted application illustration. NDR-120-24 in a cabinet with routed wiring. No SPD or surge test is shown; the image does not establish SPD coordination or measured surge protection. <a href=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/application-source.webp\" target=\"_blank\" rel=\"noopener\">View original-resolution image<\/a><\/figcaption><\/figure>\n<nav class=\"table-of-contents\" aria-label=\"Article contents\">\n<details open>\n<summary>On this page<\/summary>\n<ol>\n<li><a href=\"#a-good-spd-rating-can-be-weakened-by-cabinet-routing\">A good SPD rating can be weakened by cabinet routing<\/a><\/li>\n<li><a href=\"#count-the-path-that-carries-surge-current\">Count the path that carries surge current<\/a><\/li>\n<li><a href=\"#estimate-the-lead-contribution-before-fixing-the-layout\">Estimate the lead contribution before fixing the layout<\/a><\/li>\n<li><a href=\"#decide-what-to-change-in-the-cabinet\">Decide what to change in the cabinet<\/a><\/li>\n<li><a href=\"#verify-the-proposed-installation-in-a-defined-sequence\">Verify the proposed installation in a defined sequence<\/a><\/li>\n<li><a href=\"#prepare-the-power-supply-interface-for-review\">Prepare the power supply interface for review<\/a><\/li>\n<li><a href=\"#engineering-faq\">Engineering FAQ<\/a><\/li>\n<\/ol>\n<\/details>\n<\/nav>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_89 counter-hierarchy ez-toc-counter ez-toc-grey ez-toc-container-direction\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\" style=\"cursor:inherit\">\u0e2a\u0e32\u0e23\u0e1a\u0e31\u0e0d<\/p>\n<span class=\"ez-toc-title-toggle\"><a href=\"#\" class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" aria-label=\"Toggle Table of Content\"><span class=\"ez-toc-js-icon-con\"><span class=\"\"><span class=\"eztoc-hide\" style=\"display:none;\">\u0e2a\u0e25\u0e31\u0e1a<\/span><span class=\"ez-toc-icon-toggle-span\"><svg style=\"fill: #999;color:#999\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" class=\"list-377408\" width=\"20px\" height=\"20px\" viewbox=\"0 0 24 24\" fill=\"none\"><path d=\"M6 6H4v2h2V6zm14 0H8v2h12V6zM4 11h2v2H4v-2zm16 0H8v2h12v-2zM4 16h2v2H4v-2zm16 0H8v2h12v-2z\" fill=\"currentColor\"><\/path><\/svg><svg style=\"fill: #999;color:#999\" class=\"arrow-unsorted-368013\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"10px\" height=\"10px\" viewbox=\"0 0 24 24\" version=\"1.2\" baseprofile=\"tiny\"><path d=\"M18.2 9.3l-6.2-6.3-6.2 6.3c-.2.2-.3.4-.3.7s.1.5.3.7c.2.2.4.3.7.3h11c.3 0 .5-.1.7-.3.2-.2.3-.5.3-.7s-.1-.5-.3-.7zM5.8 14.7l6.2 6.3 6.2-6.3c.2-.2.3-.5.3-.7s-.1-.5-.3-.7c-.2-.2-.4-.3-.7-.3h-11c-.3 0-.5.1-.7.3-.2.2-.3.5-.3.7s.1.5.3.7z\"\/><\/svg><\/span><\/span><\/span><\/a><\/span><\/div>\n<nav><ul class='ez-toc-list ez-toc-list-level-1' ><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#A_good_SPD_rating_can_be_weakened_by_cabinet_routing\" >A good SPD rating can be weakened by cabinet routing<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Count_the_path_that_carries_surge_current\" >Count the path that carries surge current<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Estimate_the_lead_contribution_before_fixing_the_layout\" >Estimate the lead contribution before fixing the layout<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Hypothetical_cabinet_layout_calculation\" >Hypothetical cabinet layout calculation<\/a><\/li><\/ul><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Decide_what_to_change_in_the_cabinet\" >Decide what to change in the cabinet<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Verify_the_proposed_installation_in_a_defined_sequence\" >Verify the proposed installation in a defined sequence<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Prepare_the_power_supply_interface_for_review\" >Prepare the power supply interface for review<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Engineering_FAQ\" >Engineering FAQ<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Does_a_short_earth_lead_guarantee_protection_at_the_PSU_input\" >Does a short earth lead guarantee protection at the PSU input?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Can_thicker_SPD_cables_compensate_for_a_long_route\" >Can thicker SPD cables compensate for a long route?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Is_the_SPDs_Up_the_voltage_the_PSU_will_always_see\" >Is the SPD\u2019s Up the voltage the PSU will always see?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/www.wehopower.com\/th\/news\/spd-lead-length-power-supply-terminals\/#Can_an_ordinary_continuity_test_validate_the_surge_path\" >Can an ordinary continuity test validate the surge path?<\/a><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h2 id=\"a-good-spd-rating-can-be-weakened-by-cabinet-routing\"><span class=\"ez-toc-section\" id=\"A_good_SPD_rating_can_be_weakened_by_cabinet_routing\"><\/span>A good SPD rating can be weakened by cabinet routing<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>An external surge protective device (SPD) does not impose its catalog protection voltage directly on a power supply several connections away. The intervening conductors contribute voltage during a fast surge. A neat cabinet can therefore have a poor protection path when the SPD is installed across the enclosure and connected through spare cable loops.<\/p>\n<p>For a cabinet using the <a href=\"https:\/\/www.wehopower.com\/th\/product\/ndr-dinrail-120w-ac-to-dc-single-output-switching-power-supply\/\">WEHO NDR-120-24 DIN-rail supply<\/a>, identify the exact power supply first. WEHO\u2019s <a href=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2025\/09\/NDR-120.pdf\">\u0e04\u0e38\u0e13\u0e2a\u0e21\u0e1a\u0e31\u0e15\u0e34 NDR-120<\/a> lists the 24 V, 5 A variant. Those output ratings do not establish its input surge immunity or prove that a particular external SPD is coordinated with it.<\/p>\n<figure class=\"article-figure product\" data-asset=\"product\"><a class=\"product-image-link\" href=\"https:\/\/www.wehopower.com\/th\/product\/ndr-dinrail-120w-ac-to-dc-single-output-switching-power-supply\/\" aria-label=\"NDR-120-24 details\"><img loading=\"lazy\" src=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/ndr-120-24-product.webp\" alt=\"SPD Lead Length: Check Protection at the Power Supply Terminals  title=\" width=\"800\" height=\"800\" decoding=\"async\" spd lead length: check protection at the power supply terminals title =\"\"><\/a><figcaption>Original WEHO NDR-120-24 product photograph for model identification; it does not establish SPD coordination or installed surge immunity. <a href=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/product-source-1.jpg\" target=\"_blank\" rel=\"noopener\">View original-resolution image<\/a><\/figcaption><\/figure>\n<p>The design decision is whether the complete installed arrangement limits the relevant transient at the PSU input terminals. This article addresses connection length and routing. WEHO\u2019s <a href=\"https:\/\/www.wehopower.com\/th\/news\/what-you-need-to-know-about-surge-protection-on-power-supplies\/\">power supply surge protection overview<\/a> provides the broader starting point for surge sources and protective-device categories.<\/p>\n<h2 id=\"count-the-path-that-carries-surge-current\"><span class=\"ez-toc-section\" id=\"Count_the_path_that_carries_surge_current\"><\/span>Count the path that carries surge current<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Lead length means electrical route length, not the air gap between the SPD housing and the power supply. For the arrangement illustrated in Schneider Electric\u2019s installation guide, the counted path runs from the network connection, through any external short-circuit protective device and SPD, to the earthing terminal block. The guide recommends a total connection length no greater than 0.5 m for that arrangement. See its <a href=\"https:\/\/www.electrical-installation.org\/enwiki\/Cabling_rules_of_Surge_Protection_Device\" target=\"_blank\" rel=\"noopener\">SPD cabling rules<\/a>.<\/p>\n<p>Define the protection mode before measuring. A line-to-neutral assessment and a line-to-protective-earth assessment do not automatically contain the same conductors. Draw the relevant connection points and identify which segments carry the surge current for each mode. A single distance written beside the enclosure cannot describe every path.<\/p>\n<p>Keep the SPD connection path separate from the downstream feeder distance in the drawing. The first affects connection-induced voltage; the second can introduce additional propagation and coupling considerations. A short SPD earth lead alone cannot establish the complete installed protection level.<\/p>\n<p>The 0.5 m recommendation is a layout target tied to the illustrated installation guidance, not permission to ignore the selected SPD manual. Terminal arrangement, disconnector requirements, conductor sizing, earthing system, and local installation rules still govern the actual assembly. NEMA specifically directs installers to check the manufacturer\u2019s instructions, particularly <a href=\"https:\/\/www.nemasurge.org\/correct-installation-of-hard-wired-surge-protective-device\/\" target=\"_blank\" rel=\"noopener\">lead length and fuse or breaker requirements<\/a>.<\/p>\n<h2 id=\"estimate-the-lead-contribution-before-fixing-the-layout\"><span class=\"ez-toc-section\" id=\"Estimate_the_lead_contribution_before_fixing_the_layout\"><\/span>Estimate the lead contribution before fixing the layout<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>A simplified screening relationship is:<\/p>\n<p>U at equipment \u2248 Up + L \u00d7 di\/dt<\/p>\n<p>Here, Up is the SPD protection level under the stated test conditions, L is the effective inductance of the relevant connection path, and di\/dt is the surge-current rate of rise. The expression is a screening model; it does not include every coupling, propagation, or nonlinear effect in a complete cabinet.<\/p>\n<p>Schneider Electric\u2019s <a href=\"https:\/\/www.electrical-installation.org\/enwiki\/Connection_of_Surge_Protection_Device\" target=\"_blank\" rel=\"noopener\">connection example<\/a> uses approximately 1 \u00b5H\/m and an 8 kA current rising over 8 \u00b5s to illustrate about 1,000 V of added voltage per meter. These assumptions explain why a few extra conductor loops matter. They are not a universal conversion factor for every SPD installation.<\/p>\n<figure class=\"article-figure technical\" data-asset=\"technical\">\n<div class=\"diagram-scroll\" tabindex=\"0\" role=\"region\" aria-label=\"Scrollable engineering diagram\"><img loading=\"lazy\" src=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/spd-connection-voltage-screening.svg\" alt=\"SPD Lead Length: Check Protection at the Power Supply Terminals  title=\" width=\"1200\" height=\"675\" decoding=\"async\" spd lead length: check protection at the power supply terminals title =\"\"><\/div><figcaption>Conceptual Engineering Diagram. illustrative values and project source requirements apply. <a href=\"https:\/\/www.wehopower.com\/wp-content\/uploads\/2026\/11\/spd-connection-voltage-screening.svg\" target=\"_blank\" rel=\"noopener\">Open full-size diagram<\/a><\/figcaption><p class=\"figure-help\">Swipe horizontally on a small screen, or open the full-size diagram.<\/p>\n<\/figure>\n<h3 id=\"hypothetical-cabinet-layout-calculation\"><span class=\"ez-toc-section\" id=\"Hypothetical_cabinet_layout_calculation\"><\/span>Hypothetical cabinet layout calculation<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Assume a proposed SPD has Up = 1.5 kV at the relevant declared test condition. For this calculation only, use an effective path inductance of 1 \u00b5H\/m and a current rise of 8 kA in 8 \u00b5s. Compare two proposed connection paths: 1.20 m before rearrangement and 0.35 m after rearrangement.<\/p>\n<p>The assumed current slope is 8,000 A \u00f7 8 \u00b5s = 1,000 A\/\u00b5s. The longer path gives L = 1.20 \u00b5H and an estimated lead contribution of 1.20 \u00b5H \u00d7 1,000 A\/\u00b5s = 1.20 kV. The shorter path gives 0.35 \u00b5H \u00d7 1,000 A\/\u00b5s = 0.35 kV.<\/p>\n<div class=\"table-scroll\" tabindex=\"0\" role=\"region\" aria-label=\"Scrollable engineering table\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Screening item<\/th>\n<th scope=\"col\">Long route<\/th>\n<th scope=\"col\">Short route<\/th>\n<th scope=\"col\">Decision implication<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Counted connection path<\/td>\n<td>1.20 m<\/td>\n<td>0.35 m<\/td>\n<td>Move components before specifying extra cable.<\/td>\n<\/tr>\n<tr>\n<td>Assumed lead contribution<\/td>\n<td>1.20 kV<\/td>\n<td>0.35 kV<\/td>\n<td>Same assumed current slope and inductance per meter.<\/td>\n<\/tr>\n<tr>\n<td>Up plus lead contribution<\/td>\n<td>2.70 kV<\/td>\n<td>1.85 kV<\/td>\n<td>Use for screening, then verify the assembly.<\/td>\n<\/tr>\n<tr>\n<td>Hypothetical 2.50 kV comparison level<\/td>\n<td>Exceeds level<\/td>\n<td>Below level<\/td>\n<td>A numerical comparison alone does not establish immunity.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>The rearrangement reduces the modeled lead contribution by 0.85 kV. It does not turn the example into an NDR-120-24 test result. The assumed 2.50 kV comparison level belongs only to this example; it is not a WEHO specification, equipment withstand declaration, or acceptable surge-test level.<\/p>\n<p>An equipment insulation withstand value and a functional surge-immunity test also answer different questions. Before accepting either layout, obtain the PSU\u2019s applicable test modes, waveform, coupling method, levels, and performance criteria. An AC dielectric-strength figure cannot be substituted for that information.<\/p>\n<h2 id=\"decide-what-to-change-in-the-cabinet\"><span class=\"ez-toc-section\" id=\"Decide_what_to_change_in_the_cabinet\"><\/span>Decide what to change in the cabinet<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Shorten the connection path before treating a larger conductor as a complete remedy. NEMA explains that connecting-lead inductance adds to residual voltage and that shortening the lead has a stronger effect than a comparable practical increase in conductor size. Conductor cross-section must still satisfy the selected equipment instructions and fault-current requirements; do not reduce it merely to make routing easier.<\/p>\n<p>Separate protected outgoing conductors from the incoming surge-exposed route. Schneider\u2019s cabling guidance treats physical separation and loop-area reduction as additional measures. Bringing both routes together in the same long duct after the SPD can undermine the intended layout through coupling, even when the SPD itself sits near the incoming terminals.<\/p>\n<div class=\"table-scroll\" tabindex=\"0\" role=\"region\" aria-label=\"Scrollable engineering table\">\n<table>\n<thead>\n<tr>\n<th scope=\"col\">Observed condition<\/th>\n<th scope=\"col\">Proposed action<\/th>\n<th scope=\"col\">Record required<\/th>\n<th scope=\"col\">Verification basis<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Long SPD branch or spare loop<\/td>\n<td>Reposition SPD and connection points.<\/td>\n<td>Segment lengths for each protection mode.<\/td>\n<td>SPD instructions and installed protection assessment.<\/td>\n<\/tr>\n<tr>\n<td>External disconnector adds a detour<\/td>\n<td>Review the approved SPD\/disconnector arrangement.<\/td>\n<td>Exact device combination and route.<\/td>\n<td>Manufacturer coordination instructions.<\/td>\n<\/tr>\n<tr>\n<td>Incoming and protected routes reconverge<\/td>\n<td>Revise cable segregation.<\/td>\n<td>Annotated cabinet layout.<\/td>\n<td>Applicable routing guidance and assembly test.<\/td>\n<\/tr>\n<tr>\n<td>PSU surge information is unavailable<\/td>\n<td>Obtain the relevant report or declaration.<\/td>\n<td>Modes, levels, conditions, and criteria.<\/td>\n<td>Exact PSU revision and project requirements.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>A second SPD near the load may be a design option, but two devices cannot simply be added as independent clamps. Their coordination, connecting network, and installation conditions need an engineering basis. Likewise, do not assume a protective-earth bond through painted mounting hardware is an approved surge-current path.<\/p>\n<h2 id=\"verify-the-proposed-installation-in-a-defined-sequence\"><span class=\"ez-toc-section\" id=\"Verify_the_proposed_installation_in_a_defined_sequence\"><\/span>Verify the proposed installation in a defined sequence<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<ol>\n<li><strong>Identify the equipment and protection modes.<\/strong> Record the PSU revision, SPD part number, supply earthing arrangement, and relevant line\/neutral\/earth combinations. Check that the protection assessment covers the project\u2019s actual modes.<\/li>\n<li><strong>Measure the complete connection paths.<\/strong> Record individual conductor segments, external disconnectors, bends, and spare lengths on the drawing. Reconcile the totals with the actual installed routing, rather than the enclosure dimensions.<\/li>\n<li><strong>Check coordination documents.<\/strong> Record the SPD\u2019s applicable voltage rating, protection level, backup protection, and installation instructions. Verify the selected combination against the supply conditions and the equipment requirement; flag missing limits instead of inventing acceptance values.<\/li>\n<li><strong>Inspect route separation and bonding.<\/strong> Record incoming versus protected cable routes and the specified bonding provisions. Verify against the selected assembly and SPD instructions before energizing the cabinet.<\/li>\n<li><strong>Qualify the complete arrangement.<\/strong> Define the relevant surge tests and functional criteria with the responsible engineer or test laboratory. Record test conditions, actual assembly configuration, and results; repeat affected checks after component or routing changes.<\/li>\n<\/ol>\n<p>A continuity check can confirm an electrical connection, but it does not measure the high-frequency behavior represented by the calculation. Surge qualification requires suitable equipment and competent personnel. Keep test photos and the final routing drawing together so that production does not replace a qualified short route with a convenient long one.<\/p>\n<h2 id=\"prepare-the-power-supply-interface-for-review\"><span class=\"ez-toc-section\" id=\"Prepare_the_power_supply_interface_for_review\"><\/span>Prepare the power supply interface for review<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>For an NDR-based cabinet, use the <a href=\"https:\/\/www.wehopower.com\/th\/product\/ndr-dinrail-120w-ac-to-dc-single-output-switching-power-supply\/\">NDR-120-24 product and document entry<\/a> to identify the proposed supply. <a href=\"https:\/\/www.wehopower.com\/th\/contact\/\">Send WEHO your interface requirements<\/a> with the input system, exact PSU revision, SPD model, connection-path drawing, and required test conditions. Ask which current product documents are available for the assessment.<\/p>\n<h2 id=\"engineering-faq\"><span class=\"ez-toc-section\" id=\"Engineering_FAQ\"><\/span>Engineering FAQ<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3 id=\"does-a-short-earth-lead-guarantee-protection-at-the-psu-input\"><span class=\"ez-toc-section\" id=\"Does_a_short_earth_lead_guarantee_protection_at_the_PSU_input\"><\/span>Does a short earth lead guarantee protection at the PSU input?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. The relevant protection path includes more than the SPD earth lead. Count the applicable live-side connections and external disconnector, identify the protection mode, and assess the installed voltage at the equipment terminals.<\/p>\n<h3 id=\"can-thicker-spd-cables-compensate-for-a-long-route\"><span class=\"ez-toc-section\" id=\"Can_thicker_SPD_cables_compensate_for_a_long_route\"><\/span>Can thicker SPD cables compensate for a long route?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Thicker conductors do not eliminate the inductive penalty of unnecessary length. Select the required cross-section from the applicable instructions and fault conditions, then keep the permitted connection route short and direct.<\/p>\n<h3 id=\"is-the-spd-s-up-the-voltage-the-psu-will-always-see\"><span class=\"ez-toc-section\" id=\"Is_the_SPDs_Up_the_voltage_the_PSU_will_always_see\"><\/span>Is the SPD\u2019s Up the voltage the PSU will always see?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. Up describes the SPD under specified conditions; connecting conductors and the rest of the installation affect equipment-terminal voltage. Use matching test conditions and a complete installation assessment before comparing protection with equipment requirements.<\/p>\n<h3 id=\"can-an-ordinary-continuity-test-validate-the-surge-path\"><span class=\"ez-toc-section\" id=\"Can_an_ordinary_continuity_test_validate_the_surge_path\"><\/span>Can an ordinary continuity test validate the surge path?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. A continuity test does not establish transient inductance or functional surge immunity. It is one inspection input; the assembly still needs the documentation, routing checks, and qualification appropriate to the project.<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"<p>Check SPD lead length, connection voltage, and cabinet routing before approving power supply surge protection. Send WEHO your PSU and test requirements.<\/p>","protected":false},"author":2,"featured_media":21762,"parent":0,"menu_order":65,"comment_status":"","ping_status":"","template":"","format":"standard","meta":{"_acf_changed":false,"_joinchat":[],"footnotes":""},"news_category":[284],"class_list":["post-21796","news","type-news","status-publish","format-standard","has-post-thumbnail","hentry","news_category-product-articles","entry"],"acf":[],"post_mailing_queue_ids":[],"_links":{"self":[{"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/news\/21796","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/news"}],"about":[{"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/types\/news"}],"author":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/comments?post=21796"}],"version-history":[{"count":0,"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/news\/21796\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/media\/21762"}],"wp:attachment":[{"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/media?parent=21796"}],"wp:term":[{"taxonomy":"news_category","embeddable":true,"href":"https:\/\/www.wehopower.com\/th\/wp-json\/wp\/v2\/news_category?post=21796"}],"curies":[{"name":"\u0e2b\u0e19\u0e49\u0e32","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}