Plastic shell 5V/12V/24V/48V dc dinrail power supply 100w

MDR-100 is a slim line DIN rail Class I switching power supply.
Designed with a fully isolated plastic case to prevent user contact and the risk of shock.Featuring up to 88% efficiency this series can be cooled using only free air convection up to 60°C which significantly increases the reliability and lifetime of the power supply.Other standard features include its low no-load power consumption, to save energy, short circuit, overload, and over voltage protections, and DC OK relay contact with LED indicator for monitoring the PSU status.If you have any questions, please do not hesitate to contact us at E-mail: [email protected]

Télécharger Demander un devis

Description

Spécifications et modèle

Modèle		MDR-100-12	MDR-100-15	MDR-100-24	MDR-100-48
Sortir	DC Voltage	12V	15V	24V	48V
	Rated Current	7.5A	6.7A	4A	2A
	Current Range	0 ~ 7.5A	0 ~6.7A	0 -4A	0-2A
	Puissance nominale	100W	100W	100W	100W
	Ripple & Noise (max.)	80 mVcrête à crête	120 mVcrête à crête	150 mVcrête à crête	200 mVcrête à crête
	Volage ADJ Range	12 -13.2V	15-16.5V	24 – 26.4V	48 ~ 56V
	Voltage Tolerance	±2.0%	±1,0%	±1,0%	±1,0%
	Régulation de ligne	±1,0%	±1,0%	±1,0%	±1,0%
	Régulation de charge	±1.5%	±1,0%	±1,0%	±1,0%
	Setup, Rise Time Note.5	500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
	Hold Up Time (Typ.)	50ms/230VAC 20ms/115VAC at full load
Saisir	Voltage Range	85~264VAC 120~370VDC
	Frequency Range	47 ~ 63Hz
	Efficiency (Typ.)	78%	86%	88%	87%
	AC Current(Typ.)	1.8A/115VAC 1A/230VAC
	Inrush Current (Typ.)	Cold start: 30A/115VAC, 60A/230VAC
	Courant de fuite	<1mA/240VAC
Protection	Overload	105% – 150% rated output power
		Protection type: Constant current limiting, recovers automatically after fault condition is removed
	Overvoltage	6.25-7.25V	15.6 – 18V	31.2-36V	57.6 – 64.8V
		Protection type: Shut down o/p voltage, re-power on to recover
Fonction	DC Signal	Relay contact rating (max.): 30V/1A resistive
Environnement	Working Humidity	20% ~ 90%RH non-condensing
	Storage Temp, Humidity	-40°C ~ +85°C, 10% ~ 95%RH
	Temp Coefficient	±0.03%/°C (0 – 50°C)
	Vibration	Component: 10 – 500Hz, 2G 10min./1 cycle, the period for 60min. each along X, Y, and Z axes; Mounting: Compliance to IEC60068-2-6
Safety & EMC	Normes de sécurité	UL508, UL60950-1, TUV EN60950-1 approved
	Withstand Voltage	l/P-0/P: 3KVAC l/P-FG: 2KVAC 0/P-FG: 0.5KVAC
	Isolation Resistance	l/P-O/P, l/P-FG, 0/P-FG:>100M Ohms/500VDC/25°C/70% RH
	EMC Emission	Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3
	EMC Immunity	Compliance to EN6100(M-2,3,4,5,6,8,11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A
Autres	MTBF	299.2K hrs min. MIL-HDBK-217F (25°C)
	Dimension	5090100mm (WHD)
	Emballage	0.42Kg; 30pcs/20Kg/0.82CUFT
Note	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load, and 25°C of ambient temperature.
	2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1 uf & 47uf parallel capacitor.
	3. Tolerance: includes set up tolerance, line regulation, and load regulation.
	4. The power supply is considered a component that will be installed into the final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.
	5. The length of set-up time is measured at the first cold start. Turning ON/OFF the power supply may lead to an increase in the set-up time.